#GECKO OS BOOT.ELF INSTALL#
#GECKO OS BOOT.ELF MOD#
#GECKO OS BOOT.ELF PATCH#

After WinImage is done saving, it will conveniently open the file for you. You have now successfully backed-up your sd card and may close WinImage.ДЈ. Now that the SD card is ready, place it in Dolphin's 'Wii' folder. If you don't have an SD card, follow the steps below. If you did the above steps, you can skip the 3 steps below.ДЎ. Use this: and use WinImage to inject the data to the sd.raw.Дў. Raw, I recommend putting all the necessary files, which should be included with the mod, in a new folder (just create a new folder and put everything in it as if it were the root of an SD card.) and then using the 'inject folder' option. The reason for putting everything inside of a new folder is because the 'inject folder' option doesn't inject the folder of your choosing, it injects all the files and folders inside of it.ДЈ. Your SD card is ready, place it in Dolphin's 'Wii' folder. *Brawl doesn't support cards larger than 2 GB unless you use Riivolution instead of Gecko OS, however I have no idea if Riivolution even works in dolphin. Raws of a usb drive too, as long as it's 2GB or less. *If you're using a Nand backup of a Wii in which you use GeckoOS, you probably don't need to do this step. GeckoOS will ask for IOS 36 if you need to do it.ДЎ. Make sure 'Pack WAD' is check marked and click 'Start NUS Download!' You can click the floppy disk to choose a save destination.ДЈ. Right click Brawl's banner and set it as default iso.Дў. In this menu, click on 'Wii' and make sure 'Insert SD Card' is check marked.ДЈ.

#GECKO OS BOOT.ELF INSTALL#

Go to the 'Tools' drop-down menu and select 'Install Wad.' Find the IOS 36.wad you just created with NUS Downloader and install it.ДЄll you need to do now is click on Open, find that GeckoOS folder I told you to keep around and open its boot.elf or boot.dol file. #PROJECT M BOOT.ELF GECKOS DOLPHIN INSTALL# After this, you'll get a warning message from Dolphin. You can ignore this with no problem or disable it altogether by unchecking 'Use Panic Handlers' under the interface tab in the Config menu.

#GECKO OS BOOT.ELF MOD#

When GeckoOS loads up, just select 'Launch Game' and your mod should load up.

#GECKO OS BOOT.ELF PATCH#

There's an issue in which GeckoOS fails to use the File Patch Code correctly. If it happens to you often, This is easily fixed by going to GeckoOS' 'Config Options' and changing the 'Gecko Hook Type' to 'AXNextFrame.' #PROJECT M BOOT.ELF GECKOS DOLPHIN PATCH# You can try out other hooktypes, but this one seems to work without issues. It may have some slight graphic issues at times, but it's nothing major. *As far as I could tell, there is no difference between using GeckoOS'. I personally use the boot.elf, but use whichever you like. * It doesn't matter where you keep the GeckoOS folder in the desktop, just make sure you have the gameconfig.txt, Codes folder and, just in case, the GeckoOS folder in their respective places in the sd.raw. * You may get a white screen after skipping GeckoOS' warning message (or after running GeckoOS if you disabled panic handlers).

#PROJECT M BOOT.ELF GECKOS DOLPHIN DOWNLOAD#.

#PROJECT M BOOT.ELF GECKOS DOLPHIN MODS#.

#PROJECT M BOOT.ELF GECKOS DOLPHIN PATCH#.

#PROJECT M BOOT.ELF GECKOS DOLPHIN MOD#.

#PROJECT M BOOT.ELF GECKOS DOLPHIN INSTALL#.

Gecko os boot.elf